Breakout board Kit BRKABZ01 dual-mode Lora / Sigfox + Antennas

BRKABZ01 Breakout Experiment board based on the Lora and Sigfox Murata CMWX1ZZABZ-091 module
€71.88 €59.90
Availability: In stock
SKU
PB0002160

Murata module CMWX1ZZABZ-091 development kit

BRKABZ01 Lora / Sigfox / Multi Zones

 

This BRKABZ01 Lora / Sigfox Development Kit is a prototyping tool for learning and developing IoT soliton based on the Murata CMWX1ZZABZ-091 all-in-one open module, covering the Lora / Sigfox and FSK prototypes.

The module is powered by a STM32L072CZ and a SX1276 transceiver. The transceiver is equipped with the LoRa® long-range modem, which enables ultra-long range extended spectrum communication and high immunity to interference, reducing power consumption.

The CMWX1ZZABZ-091 is an open module, so the user has access to all STM32L072 devices such as the analog-to-digital converter, the 16-bit timer, the LP-UART, the I2C, the SPI and the USB 2.0 FS ( supporting BCD and LPM).

The LoRaWAN ™ layer is certified to class A and C standards. It is available in the I-CUBE-LRWAN package. Several examples, including a stack of AT commands, are available to help users configure a complete LoRaWAN ™ object.

The Sigfox ™ layer is RCZ1, RCZ2 and RCZ4 certified. It is available in the X-CUBE-SFOX extension package. Several examples, including an AT command modem, are also available to help users configure a complete Sigfox ™ object.

 

Attention,  the whole radio layer Lora or Sigfox is to be develop using the librairy available on the STMicroelectronics website on the following link.
Good knowledge of progamation is necessary for its implementation.

A good tutorial example of the breakout board is available on the site www.disk91.com

  

Key features: 

  • CMWX1ZZABZ-091 LoRa®/Sigfox™ module (Murata)
  • Embedded ultra-low-power STM32L072CZ Series MCUs, based on Arm® Cortex®-M0+ core, with 192 Kbytes of Flash memory, 20 Kbytes of RAM, 20 Kbytes of EEPROM
  • Frequency range: 860 MHz - 930 MHz
  • USB 2.0 FS
  • 4-channel,12-bit ADC, 2xDAC
  • 6-bit timers, LP-UART, I2C and SPI
  • Embedded SX1276 transceiver
  • LoRa®, FSK, GFSK, MSK, GMSK and OOK modulations (+ Sigfox™ compatibility)
  • +14 dBm or +20 dBm selectable output power
  • 157 dB maximum link budget
  • Programmable bit rate up to 300 kbit/s
  • High sensitivity: down to -137 dBm
  • Bullet-proof front end: IIP3 = -12.5 dBm
  • 89 dB blocking immunity
  • Low Rx current of 10 mA, 200 nA register retention
  • Fully integrated synthesizer with a resolution of 61 Hz
  • Built-in bit synchronizer for clock recovery
  • Sync word recognition
  • Preamble detection
  • 127 dB+ dynamic range RSSI

 

Power supply:

The power supply to the card is via the USB connector or the JST SB2 power connector with a maximum voltage of 5.5V DC.

 

Programming:

Programming can be done via USB connector in Micro-B format or via JTAG connector (optional adapter required)
1 software-enabled LED and 2 pushbuttons (reset and user) are present on the card.

 

The kit includes:

  • 1x Card BRKABZ01 (2.54 pitch for use on breadboard type experimental board)
  • 1x UFL RF Cable to SMA
  • 1x SMA 1/2 868Mhz RF antenna 113mm of 50 ohms
  • 1x UFL wired 868Mhz antenna
More Information
SKU PB0002160
Country of Manufacture France
Write Your Own Review
You're reviewing: Breakout board Kit BRKABZ01 dual-mode Lora / Sigfox + Antennas
Your Rating
We found other products you might like!